Ex-500.com - The home of the Kawasaki EX500 / Ninja 500R - Reply to Topic
Thread: Servicing Carb - Vacuum Line Mixup Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Ex-500.com - The home of the Kawasaki EX500 / Ninja 500R forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
4-18-2019 12:40 PM
Kevinl7778 Yeah, 3/4 of a can is surly in the engine, I have an engine in my basement that has a bent crank do to a hydrolock so def dont go cranking on the starter. Remove the plugs as mentioned and de-flood the engine before going any further.
4-17-2019 3:40 PM
ducatiman a little late now, but the carb vac line is obviously ported inboard of the throttle plates, directly into the venturi....in constant "suck mode" when the bike is cranking or running. Whatever amount of liquid was introduced via the vac line was sucked straight into the chambers, as @RickmanCR750 correctly posted.

When cranking to expel, spark plugs removed....use care and safety goggles....whatever remains in the chambers is gonna vigorously shoot straight up outta there! Dangerous to you and bodywork, etc. Loosely draping old towels over the spark plug areas a good idea, while you turn away from the mayhem.
4-16-2019 5:42 PM
AKBrickster Thanks Rickman. That's great info. Much appreciated.
4-16-2019 5:34 PM
RickmanCR750 If the engine won't turn over it sounds like you have piston lock from the Sea Foam going into the cylinders. On the compression stroke the liquid won't compress and locks the piston. I would pull the spark plugs and then when you turn over the engine the liquid will blow out the spark plug holes. You should also clean the spark plugs before putting them back in. You could also wait for the Sea Foam to leak passed the rings, hard to say how long that will take. You might also want to drain the oil because that is where the Sea Foam is going or not depending on how much got by. When the bike does start its going to smoke for a bit until the Seam Foam is burned out.
4-16-2019 5:11 PM
AKBrickster I got a pretty good amount of seafoam into... wherever it went... through the vacuum line. Probably 3/4 of a bottle. I put the rest of the bottle into the main line until it wouldn't take anymore, and opening the bowl drains shows that there is some in there.

I guess my question is if I can just drain the bowls now, hook up the gas tank, and fire it right up? I already tried that and didn't get anywhere (won't really turn over even), which made me think that the seafoam had gotten somewhere I couldn't drain off, keeping the fuel from getting to the spark plugs.

PS - The bike ran before I did this, just had to keep the choke all the way open and any throttle would kill it.
4-16-2019 5:03 PM
Kevinl7778 I think the vacuum is generated by the air rushing through the carb body or main opening, so you may have just dumped it in and it slowly dripped in to the cylinder. It should not cause any serious damage but you are still going to need to pul them and clean them the right way. Or send them to our resedent pro.
4-16-2019 4:36 PM
Servicing Carb - Vacuum Line Mixup

Hey forum,

So I'm far from being mechanically-inclined, as you'll soon find out from my current failure.

I was attempting to seafoam my carbs to see if they'd shape up after an extended period of being stored without proper stabilization. I pulled the fuel tank and drained the bowls. The intent was to put seafoam directly into the carb through the fuel line and let it sit for a couple of days to do its thing. My mistake came in the form of putting the seafoam into the vacuum line instead of the main line.

Is there any major issues with having done this? The intent was obviously to drain the seafoam from the bowls, hook the gas tank back up, and refill the carbs with fuel and just fire it up. I'm guessing I need to get the seafoam out of wherever it went by putting it in the vacuum line?

Any tips are appreciated.


Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

For the best viewing experience please update your browser to Google Chrome